Sovol Sh02 Dual Spool Filament Dryer - EU Plug

I reviewed RODRIGO FASON on YouTube, the product is of high quality, very well packaged, arrived very quickly, the seller is very attentive, responds quickly and is very helpful.

Excellent product, worked perfectly, I really liked it, I recommend it to everyone...

The dryer is very good. It's running at full capacity here.

Very good, it really does have the loud noise that people mention in the reviews, but you just need to put rubber pads on the fan, and mine has no noise at all.

Very good equipment. Easy to use, I recommend it. In places where humidity is an issue, like where I live, it is essential for good print quality.

The dryer even makes sweat on the top of the lid!! So far, 0 problems.

The product from the Brazilian warehouse is only available in the 220v version. But I put it in a transformer and it was resolved.
The dryer is very good and efficient. And so far it has been compatible with all the sizes of filament spools I have.

Very good product, there was a problem with the delivery, but the store was very transparent and resolved the issue.

A good dryer, easy to set up and with a clear interface that allows you to adjust the settings to suit your needs. Overall, I'm satisfied and recommend it.

Exceeded my expectations, compact dryer, quiet and very easy to operate.

It really is a device that delivers what it promises.

Received in very good condition, well protected and works perfectly. It makes a little noise, but since I don't have it at home, it doesn't bother me.

Quite quiet (~62dB if measured up close, ~45dB at half a meter), still inaudible against the sound of the printer. The interface is suddenly clear and understandable, displays everything you need, and even looks nice. If the humidity exceeds the permissible level, it beeps loudly; this has already helped to prevent printing from starting with excessively wet filament. During drying, the humidity dropped to 7%; I haven't seen it lower than that yet; this is probably the lower limit of the sensor. The moisture drainage hole is located at the top and is closed with a rubber plug, but it is too small. If the filament has high moisture content, it's easier to slightly open the casing (the latch allows it to be opened slightly, leaving an air gap). The holes for the thread exit are sealed in a similar manner. There are two small grooves at the bottom for silica gel, and small bags fit perfectly in them. 1kg spools fit without any problems, although for a cardboard spool with a curved geometry, I had to print plastic rings. I use it with the Sovol Zero printer.

Very nice dryer. Makes a little fan noise, buts is ok, no problem.

It starts up quickly, dries two coils at once, and sealing the housing is probably a plus. I have one single coil dryer that works in tandem with one printer, and I got this one to prepare filament for a second printer. I don't plan to print using this dryer.

The package arrived safely in two weeks, I didn't expect that ☺️ thank you so much!!! I'm satisfied with the quality of the dryer, there's no creaking, and it was packed well!

A good dryer, airtight, maintains the stated parameters accurately. The screen is informative and user-friendly.
The main downside is the lack of Russian language support, and the fact that the filament outlets are only at the front. It is not clear how the creators intend to integrate it with the printer.
The photo shows how I installed it at my place.

The product matches the description. At first glance, it seems that the quality of the product is good.

The dryer arrived quickly, bought it at a discount. At first, like with Creality, I didn't like that the humidity quickly dropped from 36% to 19%, but as it warmed up, moisture started coming out of the plastic and it began showing 22%, i.e. looks like more or less adequate sensor operation. The sensor works smoothly without glitches, the menu is intuitive, no translation needed. The MINUS for me personally is that not every spool fits in width (I often use NIT - it's too wide), but the size allows drying 2 spools at once without the possibility of printing from the dryer. And for printing from wide rolls, you can place them one at a time. I am satisfied with the quality; I'm glad I bought this one instead of Creality (like most of my equipment), I don't regret it! There are slight scuffs on top from transportation, although it was packed in a polyethylene bag, they are barely noticeable. The box is slightly dented, but everything is intact.

While using sh-01, it broke down, so I also purchased sh02. Even though the broken product is slow, after-sales service is provided. It seems that 01 is only for pla, but this one should be compatible with everything.

Pro:
- great design.
- it looks amazing.

Cons:
- it's very loud. I will replace the fan.
- the straight c7 power cable.
- 5 minutes out of the box and i'm already thinking about takining it apart and buying parts for it.
- silica gel space looks very small
- noisy rollers / bearings.

Recommendations:
- include 90 ° Cable
- replace fan

Note:
It would have fitted perfectly on the lack ikea shelf if not for the straight c7 power cable.